Bobcat S205 Skid-Steer Loader Fault Codes List

bobcat s205 skid steer loader fault codes list

Troubleshooting

If the BICS system lights are off or flashing, this may indicate a problem with the charger. The following list shows the possible effects and probable causes along with the associated service code.

Service Codes:

Means system fault (contact your Bobcat dealer for service)

Understanding the possible causes of the problem will help you to diagnose and correct the problem. If you are unsure, or if you encounter a problem that isn’t listed here, it is always best to consult a professional technician at your Bobcat dealer.

INDICATOR LIGHTLIGHT ONLIGHT OFFEFFECT ON OPERATION OF LOADER WHEN LIGHT IS OFFNO. OF FLASHESSERVICE CODECAUSES
1PRESS TO OPERATE
LOADER Button is pressed.
PRESS TO OPERATE
LOADER Button is pressed.
– – – –– – – –– – – –– – – –
2Seat Bar is down.Seat Bar is up.Lift and tilt functions will not operate.211-05Seat Bar sensor circuit shorted to battery voltage*.
2Seat Bar is down.Seat Bar is up.Lift and tilt functions will not operate.311-06Seat Bar sensor circuit shorted to ground.
2Seat Bar is down.Seat Bar is up.Lift and tilt functions will not operate.Continuous Flashing03-09System voltage low System voltage high
2Seat Bar is down.Seat Bar is up.Lift and tilt functions will not operate.Continuous Flashing03-10
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.117-07Valve output circuit is open.
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.217-05Valve output circuit shorted to battery voltage*.
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.317-06Valve output circuit shorted to ground.
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.317-06Controller not grounded or intermittent ground.
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.Continuous Flashing03-09System voltage low System voltage high
3Control valve can be used.Control valve cannot be used.Lift, tilt and traction functions will not operate.Continuous Flashing03-10
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.116-07Traction lock hold solenoid circuit is open.
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.216-05Traction lock hold solenoid circuit shorted to battery voltage*.
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.316-06Traction lock hold solenoid circuit shorted to ground.
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.515-02Traction lock pull solenoid circuit is shorted to battery voltage* – ERROR ON (Should be OFF).
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.615-03Traction lock pull solenoid circuit ERROR OFF (Should be ON).
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.Continuous Flashing03-09System voltage low
4Loader can be moved forward & backward.Loader cannot be moved forward and backward.Loader cannot be moved forward and backward.Continuous Flashing03-10System voltage high

* Normal BICS operating voltage is less than electrical system voltage.

DIAGNOSTIC SERVICE CODES

List of service codes

CODEDESCRIPTIONCODEDESCRITPTION
01-16Air filter not connected11-05Seat bar sensor short to battery
01-17Air filter plugged11-06Seat bar sensor short to ground
02-16Hydraulic charge filter not connected12-21Front auxiliary PWM switch out of range high
02-17Hydraulic charge filter plugged12-22Front auxiliary PWM switch out of range low
12-23Front auxiliary PWM switch not in neutral
03-09Battery voltage low
03-10Battery voltage high13-05Fuel shut-off hold solenoid short to battery
03-11Battery voltage extremely high13-06Fuel shot-off hold solenoid short to ground
03-14Battery voltage extremely low13-07Fuel shut-off solenoid open circuit
03-22Battery voltage out of range low
14-02Fuel shut-off pull solenoid error ON
04-09Engine oil pressure low14-03Fuel shut-off pull solenoid error OFF
04-14Engine oil pressure extremely low
04-15Engine oil pressure shutdown level15-02Traction lock pull solenoid error ON
04-21Engine oil pressure out of range high15-03Traction lock pull solenoid error OFF
04-22Engine oil pressure out of range low
16-05Traction lock hold solenoid short to battery
05-09Hydraulic charge pressure low16-06Traction lock hold solenoid short to ground
05-14Hydraulic charge pressure extremely low16-07Traction lock hold solenoid open circuit
05-15Hydraulic charge pressure shutdown level
05-21Hydraulic charge pressure out of range high17-05Hydraulic lock valve solenoid short to battery
05-22Hydraulic charge pressure out of range low17-06Hydraulic lock valve solenoid short to ground
17-07Hydraulic lock valve solenoid open circuit
06-10Engine speed high
06-11Engine speed extremely high18-05Spool Lock Solenoid short to battery
06-13Engine speed no signal18-06Spool Lock Solenoid short to ground
06-15Engine speed shutdown level18-07Spool Lock Solenoid open circuit
06-18Engine speed out of range
19-02Bucket position solenoid error ON
07-10Hydraulic oil temperature high19-03Bucket position solenoid error OFF
07-11Hydraulic oil temperature extremely high
07-15Hydraulic oil temperature shutdown level20-02Two-speed solenoid error ON
07-21Hydraulic oil temperature out of range high20-03Two-speed solenoid error OFF
07-22Hydraulic oil temperature out of range low
21-02Glow plug error ON
08-10Engine coolant temperature high21-03Glow plug error OFF
08-11Engine coolant temperature extremely high
08-15Engine coolant temperature shutdown level22-02Starter error ON
08-21Engine coolant temperature out of range high22-03Starter error OFF
08-22Engine coolant temperature out of range low
23-02Rear base solenoid error ON
09-09Fuel level low23-03Rear base solenoid error OFF
09-21Fuel level out of range high
09-22Fuel level out of range low24-02Rear rod solenoid error ON
24-03Rear rod solenoid error OFF
10-16Hydraulic implement filter not connected
10-17Hydraulic implement filter plugged

DIAGNOSTIC SERVICE CODES (CONTINUED)

Service Code List (cont’d)

CODEDESCRIPTIONCODEDESCRIPTION
11/04/1900Rear auxiliary relief solenoid error ON32-61Handle lock short to ground
12/04/1900Rear auxiliary relief solenoid error OFF32-62Handle lock short to battery
32-63Pedal lock short to ground
13/04/1900Front base solenoid error ON32-64Pedal lock short to battery
14/04/1900Front base solenoid error OFF32-65Sensor supply voltage out of range
32-66Battery voltage out of range
15/04/1900Front rod solenoid error ON32-67Switch flipped while operating
16/04/1900Front rod solenoid error OFF32-68Lift handle information error
32-69Control pattern switch flipped while operating
17/04/1900Diverter solenoid error ON32-70Right drive handle short to ground
18/04/1900Diverter solenoid error OFF32-71Right drive handle short to battery
29-02High flow solenoid error ON33-23Main Controller (Bobcat Controller) not programmed
29/03/2018High flow solenoid error OFF
34-04Keyless panel no communication to Bobcat controller
30-28Controller memory failure
35-02Two-speed fan error ON
31-28Interrupted power failure35-03Two-speed fan error OFF
32-04ACS not communicating with Bobcat Controller36-48ACD multiple controllers present
32-23ACS Not calibrated
32-31Tilt actuator fault37-02Two-speed secondary error ON
32-32Tilt actuator wiring fault37-03Two-speed secondary error OFF
32-33Tilt handle wiring fault
32-34Tilt actuator not in neutral
32-35Tilt handle / pedal not in neutral
32-36Lift actuator fault
32-37Lift actuator wiring fault
32-38Lift handle wiring fault
32-39Lift actuator not in neutral
32-40Lift handle / pedal not in neutral
32-41No communication
32-49Lift actuator short to ground
32-50Tilt actuator short to ground
32-51Lift actuator short to battery
32-52Tilt actuator short to battery
32-53Lift handle / pedal short to ground
32-54Tilt handle / pedal short to ground
32-55Lift handle / pedal short to battery
32-56Tilt handle / pedal short to battery
32-57Lift actuator reduced performance
32-58Tilt actuator reduced performance
32-59Lift actuator wrong direction
32-60Tilt actuator wrong direction
CODEDESCRIPTIONCODEDESCRIPTION
38-04No communication from joystick controller38-53Left forward drive solenoid error OFF
38-05Left joystick X axis not in neutral38-54Left reverse drive solenoid error OFF
38-06Right joystick X axis not in neutral38-55Right forward drive solenoid error OFF
38-07Left joystick Y axis not in neutral38-56Right reverse drive solenoid error OFF
38-08Right joystick Y axis not in neutral38-57Front right extend steering solenoid error OFF
38-09Control pattern switch – Short to Battery or Ground38-58Front right retract steering solenoid error OFF
38-11Lift actuator not in neutral38-59Front left extend steering solenoid error OFF
38-12Tilt actuator not in neutral38-60Front left retract steering solenoid error OFF
38-13Lift actuator fault38-61Rear right extend steering solenoid error OFF
38-14Tilt actuator fault38-62Rear right retract steering solenoid error OFF
38-15Right wheel speed fault38-63Rear left extend steering solenoid error OFF
38-16Left wheel speed fault38-64Rear left retract steering solenoid error OFF
38-17Tilt actuator reduced performance38-65Steering pressure solenoid error OFF
38-18Lift actuator reduced performance38-66Back-up alarm error OFF
38-19Left joystick X axis out of range high38-67No communication from Bobcat controller
38-20Right joystick X axis out of range low38-68Wheel angles (alignment) not calibrated
38-21Left joystick Y axis out of range high38-69Lift & tilt actuators not calibrated
38-22Right joystick Y axis out of range high38-70Interrupted power
38-23Front right steering sensor out of range high38-71Battery out of range
38-24Front left steering sensor out of range high38-72Drive pump not calibrated
38-25Rear right steering sensor out of range high38-73Steering mode / drive mode switch flipped while operating
38-26Rear left steering sensor out of range high38-74Uncommanded right wheel speed error ON
38-27Lift actuator out of range high38-75Uncommanded left wheel speed error ON
38-28Tilt actuator out of range high38-76Undercurrent steer pressure solenoid
38-29Left joystick X axis out of range low38-77Undercurrent front right extend steer solenoid
38-30Right joystick X axis out of range low38-78Undercurrent front right retract steer solenoid
38-31Left joystick Y axis out of range low38-79Undercurrent front left extend steer solenoid
38-32Right joystick Y axis out of range low38-80Undercurrent front left retract steer solenoid
38-33Front right steering sensor out of range low38-81Undercurrent rear right extend steer solenoid
38-34Front left steering sensor out of range low38-82Undercurrent rear right retract steer solenoid
38-35Rear right steering sensor out of range low38-83Undercurrent rear left extend steer solenoid
38-36Rear left steering sensor out of range low38-84Undercurrent rear left retract steer solenoid
38-375 volt sensor supply 1 out of range low38-855 Volt sensor supply 1 out of range high
38-385 volt sensor supply 2 out of range low38-865 Volt sensor supply 2 out of range high
38-39Lift actuator short to ground / out of range low38-87Front right wheel blocked (steering mechanical failure)
38-40Tilt actuator short to ground / out of range low38-88Front left wheel blocked (steering mechanical failure)
38-41Tilt actuator wrong direction38-89Rear right wheel blocked (steering mechanical failure)
38-42Lift actuator wrong direction38-90Rear left steering error
38-43Left forward drive solenoid error ON38-91Right speed sensor missing pulses
38-44Left reverse drive solenoid error ON38-92Left speed sensor missing pulses
38-45Right forward drive solenoid error ON38-93Unresponsive right speed sensor
38-46Right reverse drive solenoid error ON38-94Unresponsive left speed sensor
38-47Front right steering solenoid error ON38-98Controller in drive calibration mode
38-48Front left steering solenoid error ON38-99Controller in wheel position calibration mode.
38-49Rear right steering solenoid error ON
38-50Rear left steering solenoid error ON
38-51Steering pressure solenoid error ON
38-52Back-up alarm error ON
CODEDESCRIPTIONCODEDESCRIPTION
39-04Left joystick no communication to Bobcat controller75-22Right Joystick Y-Axis Out of Range High (H-Pattern Only)
75-27Left Swash Plate Out of Position
40-04Right joystick no communication to Bobcat controller75-28Right Swash Plate Out of Position
75-29Left Joystick X-Axis Out of Range Low
44-02Horn error ON75-31Left Joystick Y-Axis Out of Range Low
44-03Horn error OFF75-32Right Joystick Y-Axis Out of Range Low (H-Pattern Only)
75-375 Volt Sensor Supply 1 Out of Range Low
45-02Right blinker error ON75-39Left Swash Plate Sensor Out of Range High
45-03Right blinker error OFF75-40Left Swash Plate Sensor Out of Range Low
75-41Right Swash Plate Out of Range High
46-02Left blinker error ON75-42Right Swash Plate Sensor Out of Range Low
46-03Left blinker error OFF75-43Left Forward Drive Solenoid Error ON
75-44Left Reverse Drive Solenoid Error ON
47-218 volt sensor supply out of range high75-45Right Forward Drive Solenoid Error ON
47-228 volt sensor supply out of range low75-46Right Reverse Drive Solenoid Error ON
75-52Backup Alarm Error ON
48-02Front light relay error ON75-53Left Forward Drive Solenoid Error OFF
48-03Front light relay error OFF75-54Left Reverse Drive Solenoid Error OFF
75-55Right Forward Drive Solenoid Error OFF
49-02Rear light relay error ON75-56Right Reverse Drive Solenoid Error OFF
49-03Rear light relay error OFF75-66Backup Alarm Error OFF
75-67No Communication from Bobcat Controller
60-21Rear auxiliary control out of range high75-69Battery Voltage Out of Range High
60-22Rear auxiliary control out of range low75-70Interrupted Power (also occurs after software updates)
60-23Rear auxiliary control not returning to neutral75-71Battery Voltage Out of Range Low
75-72Drive Pump Not Calibrated
64-02Switched power relay error ON75-73ISO / H Pattern Switch Flipped While Operating
64-03Switched power relay error OFF75-74Right Wheel Speed Uncommanded Motion
75-75Left Wheel Speed Uncommanded Motion
74-72Bobcat controller in boot code75-76No Communication from ACS Controller
74-73Left hand panel system RX error75-77Left Speed Sensor Out of Range High
75-78Right Speed Sensor Out of Range High
75-4No Communication from Drive Controller75-79Left Speed Sensor Out of Range Low
75-5Left Joystick X-Axis Not in Neutral75-80Right Speed Sensor Out of Range Low
75-7Left Joystick Y-Axis Not in Neutral75-855-Volt Sensor Supply 1 Out of Range High
75-8Right Joystick Y-Axis Not in Neutral (H-Pattern Only)75-91Left Swash Sensor Reversed
75-9ISO / H Pattern Switch Short to Ground or Battery75-92Right Swash Sensor Reversed
75-17Left Swash Plate Not in Neutral75-93Unresponsive Right Speed Sensor
75-18Right Swash Plate Not in Neutral75-94Unresponsive Left Speed Sensor
75-21Left Joystick Y-Axis Out of Range High75-95Left Speed Sensor Reverse Direction
75-19Left Joystick X-Axis Out of Range High75-96Right Speed Sensor Reverse Direction
75-21Left Joystick Y-Axis Out of Range High (H-Pattern Only)75-98Controller in Calibration Mode
CODEDESCRIPTION
77-48Key Switch
78-74Door / Transport Lock
80-02ACD output ‘A’ error ON Door Transport Lock
80-03ACD output ‘A’ error OFF
81-02ACD output ‘B’ error ON
81-03ACD output ‘B’ error OFF
82-02ACD output ‘C’ error ON
82-03ACD output ‘C’ error OFF
83-02ACD output ‘D’ error ON
83-03ACD output ‘D’ error OFF
84-02ACD output ‘E’ error ON
84-03ACD output ‘E’ error OFF
85-02ACD output ‘F’ error ON
85-03ACD output ‘F’ error OFF
86-02ACD output ‘G’ error ON
86-03ACD output ‘G’ error OFF
87-02ACD output ‘H’ error ON
87-03ACD output ‘H’ error OFF
90-02Service tool output ‘C’ error ON
90-03Service tool output ‘C’ error OFF
91-02Service tool output ‘D’ error ON
91-03Service tool output ‘D’ error OFF
92-02Service tool output ‘E’ error ON
92-03Service tool output ‘E’ error OFF
93-02Service tool output ‘F’ error ON
93-03Service tool output ‘F’ error OFF