Bobcat fault codes

bobcat fault codes

Bobcat mini-loader fault codes will help you identify the faulty actuator and quickly repair the faulty mechanism of both the engine and hydraulic system.

Fault codeDescription
01-16Air filter not connected
01-17Air filter clogged
02-16Hydraulic pressure filter not connected.
02-17Hydraulic pressure filter clogged
03-09Low battery voltage
03-10High battery voltage
03-11Extremely high battery voltage
03-14Extremely low battery voltage
03-22The battery voltage is below the maximum allowable
04-09Low engine oil pressure
04-14Extremely low engine oil pressure
04-15Oil pressure in the engine at the level of emergency engine shutdown
04-21Engine oil pressure above maximum permissible
04-22Engine oil pressure below the maximum allowable
05-09Low recharge pressure in hydraulic system
05-14Extremely low make-up pressure in the hydraulic system
05-15Feed pressure in the hydraulic system at the level of emergency engine shutdown
05-21Feed pressure in the hydraulic system is higher than the maximum allowable
05-22Feed pressure in the hydraulic system is below the maximum allowable
06-10High engine speed
06-11Extremely high engine rpm
06-13No engine speed signal
06-15Engine speed at the level of emergency engine shutdown
06-18Engine speed outside permissible limits
07-10High hydraulic oil temperature
07-11Extremely high hydraulic oil temperature
07-15Oil temperature in the hydraulic system at the level of emergency engine shutdown
07-21Oil temperature in the hydraulic system is higher than the maximum allowable
07-22Oil temperature in the hydraulic system below the maximum allowable
08-10High engine coolant temperature
08-11Extremely high engine coolant temperature
08-15Engine coolant temperature at the level of emergency engine shutdown
08-21Engine coolant temperature is above the maximum allowable
08-22Engine coolant temperature below the maximum allowable
09-09Low fuel level
09-21Fuel level above the maximum allowable
09-22The fuel level is below the maximum allowable
11-05Safety frame sensor shorted to battery
11-06Safety frame sensor shorted to ground
12-21Signal PWM controller front ext. hydraulics beyond the upper limit of the range
12-22PWM controller front ext. hydraulics beyond the low end of the range
12-23PWM controller front ext. non-neutral hydraulics
13-05Fuel shut-off holding solenoid shorted to battery
13-06Holding solenoid fuel cutoff shorted to ground
13-07Open circuit of fuel cut-off solenoid
14-02Fuel cut-off solenoid, erroneous switch on
14-03Fuel shut-off solenoid, erroneous shutdown
15-02Retractable solenoid locking thrust, erroneous inclusion
15-03Retractable solenoid locking thrust, erroneous shutdown
16-05Holding solenoid lockout closed on battery
16-06Holding solenoid blocking thrust closed to ground
16-07Open circuit retaining solenoid blocking traction
17-05Solenoid hydraulic shut-off valve shorted to battery
17-06Solenoid hydraulic shut-off valve shorted to ground
17-07Open circuit of the solenoid hydraulic shut-off valve
18-05The solenoid of the valve is closed to the battery
18-06Solenoid spool closed to ground
18-07Open circuit of the spool solenoid
19-02Bucket positioning solenoid, erroneous switch on
19-03Solenoid bucket positioning, erroneous shutdown
20-02Solenoid switching speeds erroneous inclusion
20-03Solenoid switching speeds erroneous shutdown
21-02Glow plugs, erroneous inclusion
21-03Glow plugs, erroneous shutdown
22-02Starter, erroneous inclusion
22-03Starter, mistaken shutdown
23-02Rear Base Solenoid, Incorrect Inclusion
23-03Rear base solenoid, faulty shutdown
24-02Rear stock solenoid, erroneous switch on
24-03Rear stock solenoid, erroneous shutdown
25-02Rear Auxiliary Proportional Solenoid, Incorrect Inclusion
25-03Rear auxiliary proportional solenoid, erroneous shutdown
26-02Incorrect inclusion of the front base solenoid
26-03Wrong shutdown of the front base solenoid
27-02Incorrect inclusion of the front stock solenoid
27-03Wrong shutdown of the front stock solenoid
28-02Incorrect inclusion of diverter solenoid
28-03Erroneous diverter solenoid shutdown
29-02Large feed solenoid, erroneous switch on
29-03Large feed solenoid, faulty shutdown
30-28Controller memory failure
31-28Recovery Mode Malfunction
32-04Extended Control (ACS) does not communicate with the Bobcat controller
32-23Extended ACS Management Not Calibrated
32-31Tilt actuator failure
32-32Malfunctioning wiring of the tilt actuator
32-33Faulty wiring tilt bucket handle
32-34Tilt actuator not in neutral
32-35Bucket tilt lever / pedal not in neutral position
32-36Lift actuator failure
32-37Faulty wiring actuator lifting
32-38Faulty wiring of boom lift handle
32-39Actuator not in neutral
32-40Arm / boom pedal not in neutral position
32-41No connection
32-49Lifting actuator shorted to ground
32-50Tilt actuator shorted to ground
32-51Lifting actuator shorted to battery
32-52Tilt actuator shorted to battery
32-53Arm / Boom Lift Pedal Closed to Ground
32-54The handle / pedal tilt bucket closed to ground
32-55Arm / Boom Lift Pedal Closed to Battery
32-56The handle / pedal tilt bucket closed on the battery
32-57Reduced lift actuator performance
32-58Reduced tilt actuator performance
32-59Wrong direction of the lifting actuator
32-60Incorrect direction of tilt actuator
32-61Handle lock closed to ground
32-62Handle lock closed on battery
32-63The pedal lock circuit is shorted to ground
32-64The pedal lock circuit is closed to battery
32-65Sensor supply voltage outside permissible limits
32-66Battery voltage out of range
32-67Switch switched during operation
32-68Information error arm lifting boom
32-69Control switch switched during operation
32-70The chain of the right-hand grip is closed to ground
32-71The chain of the right grip movement is closed on the battery
33-23Main controller ( Bobcat controller ) not programmed
34-04The pushbutton panel does not communicate with the Bobcat controller
35-02Two-speed fan switch, erroneous on
35-03Two-speed fan switch, erroneous shutdown
36-48Multiple ACD controllers connected
37-02Two-speed additional speed selector, erroneous start
37-03Two-speed optional speed switch, erroneous shutdown
38-04No connection to joystick controller
38-05X axis of the left joystick is not in neutral position
38-06X axis of the right joystick is not in neutral
38-07Y axis of the left joystick is not in neutral position
38-08Y axis of the right joystick is not in neutral
38-09Control mode switch – short to battery or ground
38-11Actuator not in neutral
38-12Tilt actuator not in neutral
38-13Lift actuator failure
38-14Tilt actuator failure
38-15Faulty wheel speed control wiring
38-16Fault wiring for left wheel speed
38-17Reduced tilt actuator performance
38-18Reduced lift actuator performance
38-19X axis of the left joystick, beyond the upper limit of the range
38-20X axis of the right joystick, beyond the lower limit of the range
38-21Y axis of the left joystick, beyond the upper limit of the range
38-22Y axis of the right joystick, beyond the upper limit of the range
38-23The signal of the front right sensor control for the upper limit of the range
38-24The signal of the front left sensor control for the upper limit of the range
38-25The signal of the rear right control sensor beyond the upper limit of the range
38-26The signal of the rear left sensor control for the upper limit of the range
38-27Lift actuator signal over upper range limit
38-28Tilt actuator signal above upper range limit
38-29X axis of the left joystick, beyond the lower limit of the range
38-30X axis of the right joystick, beyond the lower limit of the range
38-31Y axis of the left joystick, beyond the lower limit of the range
38-32Y axis of the right joystick, beyond the lower limit of the range
38-33The signal of the front right control sensor for the lower limit of the range
38-34The signal of the front left control sensor for the lower limit of the range
38-35The signal of the rear right control sensor for the lower limit of the range
38-36The signal of the rear left control sensor for the lower limit of the range
38-37Power supply “1” 5-volt sensor, beyond the lower limit of the range
38-38Power supply “2” 5-volt sensor, beyond the lower limit of the range
38-39Actuator lifting closed to ground / beyond the lower limit of the range
38-40Tilt actuator shorted to ground / signal beyond low range
38-41Incorrect direction of tilt actuator
38-42Wrong direction of the lifting actuator
38-43Solenoid left front drive, erroneous inclusion
38-44Solenoid of the left reversive drive, wrong inclusion
38-45Solenoid of the right front drive, erroneous inclusion
38-46Solenoid of the right reverse drive, erroneous inclusion
38-47Front right control solenoid, erroneous switch on
38-48Front left control solenoid, erroneous switch on
38-49Rear right control solenoid, erroneous switch on
38-50Rear left control solenoid, erroneous switch on
38-51Control pressure solenoid, erroneous switch on
38-52Reverse signal, erroneous activation
38-53Solenoid left front drive, erroneous shutdown
38-54Solenoid of the left reversive drive, wrong shutdown
38-55Solenoid right front drive, erroneous shutdown
38-56Solenoid of the right reversive drive, wrong shutdown
38-57Front right solenoid advance control, erroneous shutdown
38-58Front right solenoid control retract, erroneous shutdown
38-59Front left extension control solenoid, faulty shutdown
38-60Front left solenoid control retract, erroneous shutdown
38-61Rear right firing solenoid, erroneous shutdown
38-62Rear right solenoid control retract, erroneous shutdown
38-63Rear left advance control solenoid, faulty shutdown
38-64Rear left solenoid control retract, erroneous shutdown
38-65Solenoid pressure control system, erroneous shutdown
38-66Reverse signal, erroneous shutdown
38-67No messages from Bobcat controller
38-68Wheel alignment angles (alignment) not calibrated
38-69Lifting and tilting actuators not calibrated
38-70Power down
38-71Battery voltage out of range
38-72Drive Pump Not Calibrated
38-73Control mode / motion mode switch switched during operation
38-74Unmanaged right wheel speed
38-75Unmanaged left wheel speed
38-76Solenoid pressure control system – insufficient current
38-77Front Right Solenoid Extend Control – Insufficient Current
38-78Front Right Solenoid Control – Low Current
38-79Front Left Extend Control Solenoid – Insufficient Current
38-80Front Left Solenoid Control Retractor – Insufficient Current
38-81Rear Right Solenoid Extend Control – Insufficient Current
38-82Rear right solenoid inlet control – insufficient current
38-83Rear Left Extension Control Solenoid – Insufficient Current
38-84Rear Left Solenoid Control Retractor – Insufficient Current
38-85Power supply “1” 5-volt sensor beyond the upper limit of the range
38-86Power supply “2” 5-volt sensor beyond the upper limit of the range
38-87Lock the right front wheel (mechanical control failure)
38-88Lock the left front wheel (mechanical control failure)
38-89Lock the right rear wheel (mechanical control failure)
38-90Rear left control error
38-91No wheel speed sensor pulses
38-92No left wheel speed sensor pulses
38-93Right wheel speed sensor not responding
38-94Left wheel speed sensor not responding
38-98Controller in drive calibration mode
38-99Controller in wheel position calibration mode
45-03Right direction indicator, wrong shutdown
46-02Left turn signal, erroneous inclusion
46-03Left direction indicator, erroneous shutdown
47-21Power supply 8-volt sensor beyond the upper limit of the range
47-22Power supply 8-volt sensor, beyond the lower limit of the range
48-02Front light relay erroneous on
48-03Front light relay erroneous shutdown
49-02Reverse light switch
49-03Relay backlight, erroneous shutdown
60-21Signal control lever rear ext. hydraulics beyond the upper limit of the range
60-22Signal control lever rear ext. hydraulics beyond the lower limit of the range
60-23Control lever rear ext. hydraulically does not return to neutral
64-02Incorrect power switch on
64-03Faulty power down
74-72Bobcat controller boot code failure
74-73Left panel, receiver error
80-02ACD, output “A”, wrong inclusion
80-03ACD, output “A”, wrong shutdown
81-02ACD, output “B”, wrong switch
81-03ACD, output “B”, wrong shutdown
82-02ACD, output “C”, wrong inclusion
82-03ACD, output “C”, wrong shutdown
83-02ACD, output “D”, wrong switch
83-03ACD, output “D”, wrong shutdown
84-02ACD, output “E”, wrong switch
84-03ACD, output “E”, wrong shutdown
90-02Service output “C”, erroneous activation
90-03Service output “C”, erroneous shutdown
91-02Service output “D”, erroneous activation
91-03Service output “D”, erroneous shutdown
92-02Service exit “E”, erroneous inclusion
92-03Service output “E”, erroneous shutdown
93-02Service output “F”, erroneous start
93-03Service output “F”, erroneous shutdown